WOREMOR Shielding Wallpaper GRAY | HF + LF | Width 100 cm

Order quantity: In measures of 1.0 running meters. This product is cut off according to your specifications, a return or revocation are not possible.
Screening attenuation: All stated attenuation values apply at 1 Ghz. Measurement to ASTM D4935-10 or IEEE Std 299-2006 or IEEEE Std 1128-1998 or ASTM A698/A698M-07. You find the test report above under "Report screening attenuation".
Grounding: Electrically conductive. Can be contacted and grounded to shield electric fields (LF). Please find corresponding components under "Grounding". A recommendation here is difficult because this depends on the application. Please ask us!
Application: Ceiling, Floor, Wall interior
Field type: LF (Low frequency alternating electrical fields), HF (High frequency electromagnetic fields)
Ecology: Very high
Color: Gray


The WP-Series are one-side metallized wallpapers for the shielding of high-frequency radiation (HF) and low-frequency electric fields (LF). The basis for this products is a white wallpaper base, certified to FSC© Mix Credit, from the worldwide biggest manufacturer. This wallpaper has a very high dimension stability before, while and after processing.

Special feature

Very high ecology: Almost all EMC shielding products become metallized in a “chemical” procedure. A lot of chemicals are needed for the production of copper- and nickel-layers. Our new coating process allows to completely apply the metal on the base material with the use of air and green electricity only, without chemicals. The ecological awareness for this is very high. High vapor permeability: Instead of an area-wide application the metal alloy is applied spattered on the base material.


Only interior on walls and ceilings as base wallpaper. Applicable for loose laying, if the wallpaper is protected against mechanical damage.

Technical data


  • Width: 100 cm
  • Length: By the meter, 20 m roll, 100 m roll
  • Attenuation: 60 dB
  • Weight: 190 g/m²
  • Thickness: 0.20 mm
  • Tensile strenght: 2.7 - 4.4 kN/m
  • Color: Gray
  • sD-value: Upcoming
  • Surface conductivity: 0.04 Ohm (Square resistance)



  • Width: 100 cm
  • Length: By the meter, 20 m roll, 100 m roll
  • Attenuation: 80 dB
  • Weight: 230 g/m²
  • Thickness: 0.21 mm
  • Tensile strenght: 2.7 - 4.4 kN/m
  • Color: Gray
  • sD-value: Upcoming
  • Surface conductivity: 0.008 Ohm (Square resistance)



  • Width: 100 cm
  • Length: By the meter, 20 m roll, 50 m roll
  • Attenuation: 100 dB
  • Weight: 340 g/m²
  • Thickness: 0.22 mm
  • Tensile strenght: 2.7 - 4.4 kN/m
  • Color: Gray
  • sD-value: Upcoming
  • Surface conductivity: 0.004 Ohm (Square resistance)


Loose laying / stapling: Always overlap the single elements for at least 5 cm. Do consider that there should be no gaps / holes.

Bonding the metallized surface in direction wall: The issue is, that for a proper grounding, the sheets must be electrically connected with each other. Usually this is attained by using the grounding strap EB1, which is connecting the single sheets with each other. When bounding the sheets with the metallized surface in direction wall this is not possible. If you still decide to do though, you will have to apply the grounding strap EB1 to the wall first and then adhere the sheets with standard wallpaper paste onto the wall. This will give a slightly chance that the metallized side will be contacted with EB1. Because this depends on the glue, we recommend to carry out experiments.

Bonding the metallized surface in direction room: This is the best solution, even though the result is not so nice. But in return, all sheets subsequent can easily be connected with EB1 and grounded then.

Edge to edge or overlapping: Ideally the sheets should be glued on overlapping to achieve the best attenuation. As a next step the overlapping should be smoothed with a fine filler. However, you wont achieve a perfect even surface. Alternatively you can glue on the sheets edge to edge as normal for wallpapers. This will cause a low loss of attenuation.